Community C6-B Manual de usuario descargar pdf (Pagina 2)

The Commercial Design Series (CDS) Can Adapter/Trim Ring

(CATR) is intended for use when a CDS ceiling loudspeaker is

being mounted in either an existing oversize hole in the ceiling

or when the entire CDS ceiling loudspeaker can assembly is

being mounted inside of an existing, larger, industry standard-

type back can.

Using the CATR with an Existing Oversize Hole

If the CDS ceiling loudspeaker is being fitted into an existing

oversize hole of up to 11 inches (279 mm) in diameter or if the

CDS loudspeaker is being inserted into a previously installed

larger industry back can, then you can use a CATR to dress

the installation.

There are three models of the Can Adapter/Trim Ring. The C4-

CATR is used for retrofit installations of an entire C4LP & C4

complete assembly into an existing larger industry back can or

into an existing but oversize ceiling hole. The C6-CATR and

C8-CATR do the same for C6 and C8 complete assemblies

respectively.

NOTE: Before mounting a loudspeaker into an oversize hole

using the CATR, insert the provided rubber hole plugs into the

four countersunk holes on the CATR that will face outward.

Insert the plugs, pull them through from the rear side firmly and

cut the excess length off of the plugs from the rear side so that

they do not interfere with installation. You will not need to use

the provided 8-32 screws in this application and you should not

need to use the provided clamp extenders.

When using a CATR to mount a CDS loudspeaker into an

oversize hole, it is recommended that the user also use the

standard tile rails behind the ceiling whenever possible for the

best possible weight distribution and support. Rotate the back

can as necessary to ensure all of the clamps are oriented to

contact the tile rails.

Existing Ceiling

Tile Rail Bridges

CATR (Can Adapter Trim Ring)

CDS Complete Assembly (Back

Can Showing Drop-Stop™ Tabs)

Figure 1:

Suggested use of CATR being used in an oversize hole

CAN ADAPTER / TRIM RING (CATR)

Using the CATR with an Existing Industry Back Can

You can use a CATR to install a C4, C4LP, C6 or C8 complete

loudspeaker assembly, including the back can, into an existing

larger back can. This is the “Adapter” function of the CATR.

Leave the existing back can and its tile rails (if any) in place.

Using the four (4) supplied 8-32 screws, mount the CATR into

the existing back can using the existing screw inserts on the

can, taking care to center the CATR (Note: You will not need to

use the hole plugs in this application).

Before installing the CDS loudspeaker into the existing back

can you must install the provided Clamping Extenders onto the

ceiling loudspeaker clamping feet. Simply slide the plastic

clamp extenders over the feet. For the best performance align

the outer edge of the extender with the outer edge of the

existing clamp. Make sure to fold the clamps back against the

can before proceeding to install the loudspeaker. Once that is

completed, you can open the Drop-Stop™ tabs slightly, insert

the CDS loudspeaker back can through the CATR, listening for

the Drop-Stop tabs to snap into position. Then turn the Phillips-

head Can-Locking Clamp Actuator screws in the CDS can so

that it is secured in place, following the same procedure

recommended in the Commercial Design Series Ceiling

Installation and Operation Manual for standard ceiling

loudspeaker installation.

Existing Back Can and Tile Rails

CATR (Can Adapter Trim Ring)

CDS Complete Assembly

(Back Can with Drop-Stop™ Tabs Shown)

Figure 2:

C6-CATR used to fit an entire assembled C6 into a

larger existing back can

Parts Supplied with Can Adapter / Trim Ring (CATR)

C4-CATR / C6-CATR / C8-CATR

(2) Clamp Extender

(4) Trim Ring Screw Hole Plug

(4) 8-32x1 Oval Head Screw, White

(1) Can Adapter / Trim Ring

(4) .177" [4.5mm] Countersunk HOLES ON A

11.250" [285.75mm] B.C.

O.D. = 12.750" [323.85mm]

I.D. C4-CATR = 7.303"

[185.5mm]

I.D. C6-CATR = 8.799"

[223.5mm]

I.D. C8-CATR = 10.299"

[261.6mm]

Figure 3:

C4-CATR, C6-CATR and C8-CATR dimensional drawings

1 2 3 4

Comentarios a estos manuales

Sin comentarios

Community C6-B Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Altavoces barra de sonido Community C6-B